PDA

View Full Version : FREE - N600+ MTS LiveWire Permanent Unlock


Shadab Ahmad
07-17-2012, 08:06 PM
Hi All!

You can Unlock your N600+ MTS LiveWire permanently.

Just need a few files to be downloaded.

Download MTS Original Firmware ([Only registered and activated users can see links] 8%83/new/3G/%E8%BD%AF%E4%BB%B6/157750B0513V.MTS.SP100.B04.zip)

Download Chinese Firmware ([Only registered and activated users can see links] 8%83/%E5%A4%96%E5%8D%8F%E5%8E%82%E5%AE%B6/N600PLUSV1.0.1B06.zip)

Download Flasher ([Only registered and activated users can see links])

Extract firmware to any folder of your choice.
Install Flasher.

Now start flasher. On login screen, you will see strange characters.
Don't worry, just click on OK.

Now software will open, Click on English Version. Close flasher and again Run.

Now you will see Username and Password dialog. Type in the following:
User: Administrator
Pass: ZTEsmt123
and click OK.

Now flasher will start with all options enabled.

Connect phone in FTM mode by holding Volume Down Key and Power Key.

If you need driver, it is in our Support Area's ([Only registered and activated users can see links]) \Driver Folder.

Note down COMM Port in device manager (ZTE Diagnostic Port - DFU, something similar).

In flasher, goto Option > Port Config, and select noted COMM Port in Line1-DIAG and click OK.

Now flasher will show your phone information in main windows against Line 1 (1:).

Now, in Download Settings, Mark on Download CEFS. A message will come, simply click OK on that message.

In Config Group, select No Backup and Restore.

Click on SW Directory and select folder where you extracted Firmware.

Now Click on Arrow ( -> ) against your Line where phone information is being displayed (eg. Line1 ).

Flashing will start and will take something around 3 minutes.

Close flasher, do not disconnect phone, leave it connected in FTM mode.

Now start MultiFuN CDMA ZTE Module, select phone COMM Port, select Model as N600+ LiveWire and click on SP Unlock. Software will give you information that Unlocking was successful. :cool:

If you have any other tool supporting this Model, you can use that tool too.

Now, you can use your phone with any Carrier, no need to unlock it again and again.

Enjoy! ;)

Br,
Shadab Ahmad

Rahul_Bhutani
07-17-2012, 08:34 PM
firmware link is dead check and fix it.

Shadab Ahmad
07-17-2012, 09:27 PM
firmware link is dead check and fix it.

Thanks for reporting...

Fixed now :)

Br,
Shadab Ahmad

aksharasofts
07-19-2012, 12:37 PM
will android will work after flashing with flasher


mobile software will be same of mts or it will be changed

Shadab Ahmad
07-19-2012, 12:45 PM
will android will work after flashing with flasher


mobile software will be same of mts or it will be changed
It will be same as before.

Br,
Shadab Ahmad

rahul_rocks3
07-19-2012, 07:49 PM
will android will work after flashing with flasher


mobile software will be same of mts or it will be changed

Everything will be same brother.

skcdma
07-20-2012, 01:46 AM
will android will work after flashing with flasher


mobile software will be same of mts or it will be changed

Yes 100% working i m chk..

Any pro cont: on yahoo / google..





MultiFun Team

alokmingma
07-20-2012, 10:33 AM
dear members after doing full unlock with flashing meid become ooooooooo in that case no internet will work on n600+ and there will no edit option in acess point setting .

to fix this problem you just write meid of handset again in it by multifun tool

internet will work

100% chked

KASANADS
07-21-2012, 04:37 PM
I am unable to download the multi fun tool how do i do it

Shadab Ahmad
07-21-2012, 08:48 PM
You can download it from our Download Area [Only registered and activated users can see links]

Username/Password: multifun

Br,
Shadab Ahmad

KASANADS
07-22-2012, 12:20 AM
You can download it from our Download Area [Only registered and activated users can see links]

Username/Password: multifun

Br,
Shadab Ahmad
I have downloaded the file and replaced the exe file also but both the same files are same

Shadab Ahmad
07-22-2012, 01:47 PM
I have downloaded the file and replaced the exe file also but both the same files are same
What do you exactly mean by "SAME" ???

You must have Licence to use this tool.

Br,
Shadab Ahmad

Rahul_Bhutani
07-22-2012, 03:15 PM
I have downloaded the file and replaced the exe file also but both the same files are same
it is a paid tool not free,for buy license contact to shadab online.

aksharasofts
07-24-2012, 01:13 PM
Yes 100% working i m chk..

Any pro cont: on yahoo / google..





MultiFun Team

please post u r yahoo id

KASANADS
07-24-2012, 08:02 PM
zte_setup_01.rar, and MF_CDMA_ZTE_2d.rar are same there is no difeerence

Shadab Ahmad
07-24-2012, 10:54 PM
zte_setup_01.rar, and MF_CDMA_ZTE_2d.rar are same there is no difeerence
zte_setup_01.rar is Main Installation Package, where as MF_CDMA_ZTE_2d.rar is the updated EXE only.

At first, you need to install Main Installation Package, and then download updated EXE and overwrite old EXE.

Br,
Shadab Ahmad

KASANADS
08-01-2012, 02:47 PM
I have done as u said but same window is opening after changing the exe file. pls help and my mobile is not coming out of ftm mode

KASANADS
08-01-2012, 02:47 PM
I have done as u said but same window is opening after changing the exe file. pls help and my mobile is not coming out of ftm mode

rahul_rocks3
08-01-2012, 05:25 PM
I have done as u said but same window is opening after changing the exe file. pls help and my mobile is not coming out of ftm mode

First install the mail installation package then right click on multifun zte icon and go to open file location, then replace the exe file with the other downloaded exe. And then try running the same and post results. If still not solved come online on yahoo will help you out.

Regards,
Multifun Team.

KASANADS
08-08-2012, 10:31 PM
I have tried the same again how do i come online

KASANADS
08-08-2012, 10:51 PM
First install the mail installation package then right click on multifun zte icon and go to open file location, then replace the exe file with the other downloaded exe. And then try running the same and post results. If still not solved come online on yahoo will help you out.

Regards,
Multifun Team.

I have repeated the process again but the new exe file is the same as the previous on there is no change how do i come online and contact u

Shadab Ahmad
08-08-2012, 11:38 PM
I have repeated the process again but the new exe file is the same as the previous on there is no change how do i come online and contact u
Hi!

What problem EXACTLY your are getting?

Are you a customer of MultiFuN Tool? Do you have LIC file?

Br,
Shadab Ahmad

rahul_rocks3
08-09-2012, 12:58 AM
I have repeated the process again but the new exe file is the same as the previous on there is no change how do i come online and contact u

Are you a registered user of MultiFun Tool. If yes then come online on yahoo and share your yahoo id over here.

alokmingma
08-09-2012, 09:34 AM
call me I will help u online 969xxxxxxx

KASANADS
08-09-2012, 10:42 PM
Hi!

What problem EXACTLY your are getting?

Are you a customer of MultiFuN Tool? Do you have LIC file?

Br,
Shadab Ahmad


How do i get the LIC and what is the cost

skcdma
08-10-2012, 01:09 AM
How do i get the LIC and what is the cost


Hello Bro:

See Here: [Only registered and activated users can see links]







MultiFun Team

rahulg007
08-31-2012, 12:07 AM
can anybody provide me spc code for this phone???
and process of repairing it wifi mac address

user.name
09-23-2012, 01:20 AM
WiFi MAC address recovery
Preparation
Download and Install QPST 2.7 Build 366
Download and Install Hexedit for windows


Recovery mac address wifi
Turn off the mts livewire
Press and hold power + volume[+] buttons until it`s boot to Field Test Mode (FTM).
In PC, start > QPST
Add Port for ZTE in QPST
Open QPST Configuration
Port > Add New Port
Choose COMxx ZTE Handset Diagnostic Interface (DFU)
Click OK
Start Client > Software Download
Select backup dan backup nvitems
Run hex editor
open .qcn (this is a backup file that you get from step 4)
Find 11 22 33 44 55 66
Edit to original mac address, if you dont have the MAC address try with MAC address bluetooth (give the different address with up/down one number)
save file
back to software download
select restore tab
select fire .qcn that already edited
Your WiFi should be back right now.
WARNING!! Use QPST and qcn edit file carefully. This method have a change to make your tablet completely useless (unrecover brick)
Do With Your Own Risk

user.name
09-23-2012, 01:25 AM
Hi All!

You can Unlock your N600+ MTS LiveWire permanently.

Just need a few files to be downloaded.

Download MTS Original Firmware ([Only registered and activated users can see links] 8%83/new/3G/%E8%BD%AF%E4%BB%B6/157750B0513V.MTS.SP100.B04.zip)

Download Chinese Firmware ([Only registered and activated users can see links] 8%83/%E5%A4%96%E5%8D%8F%E5%8E%82%E5%AE%B6/N600PLUSV1.0.1B06.zip)

Download Flasher ([Only registered and activated users can see links])

Extract firmware to any folder of your choice.
Install Flasher.

Now start flasher. On login screen, you will see strange characters.
Don't worry, just click on OK.

Now software will open, Click on English Version. Close flasher and again Run.

Now you will see Username and Password dialog. Type in the following:
User: Administrator
Pass: ZTEsmt123
and click OK.

Now flasher will start with all options enabled.

Connect phone in FTM mode by holding Volume Down Key and Power Key.

If you need driver, it is in our Support Area's ([Only registered and activated users can see links]) \Driver Folder.

Note down COMM Port in device manager (ZTE Diagnostic Port - DFU, something similar).

In flasher, goto Option > Port Config, and select noted COMM Port in Line1-DIAG and click OK.

Now flasher will show your phone information in main windows against Line 1 (1:).

Now, in Download Settings, Mark on Download CEFS. A message will come, simply click OK on that message.

In Config Group, select No Backup and Restore.

Click on SW Directory and select folder where you extracted Firmware.

Now Click on Arrow ( -> ) against your Line where phone information is being displayed (eg. Line1 ).

Flashing will start and will take something around 3 minutes.

Close flasher, do not disconnect phone, leave it connected in FTM mode.

Now start MultiFuN CDMA ZTE Module, select phone COMM Port, select Model as N600+ LiveWire and click on SP Unlock. Software will give you information that Unlocking was successful. :cool:

If you have any other tool supporting this Model, you can use that tool too.

Now, you can use your phone with any Carrier, no need to unlock it again and again.

Enjoy! ;)

Br,
Shadab Ahmad
@Shadab Ahmad - after unlocking meid become 0000000.. when i rewrite meid then its locked again.. any solution for that?

thanx..

Shadab Ahmad
09-23-2012, 02:20 AM
@Shadab Ahmad - after unlocking meid become 0000000.. when i rewrite meid then its locked again.. any solution for that?

thanx..
Not till now.

Br,
Shadab Ahmad

rahulg007
09-23-2012, 01:32 PM
bro i tried this method but i was nt able to backup the phone

Shadab Ahmad
09-23-2012, 11:00 PM
Anyone who have this phone in hand, contact me on Sonork.

You must have activation for MultiFuN Tool.

Repair WIFI MAC Address and BT Address in One Click.

Br,
Shadab Ahmad

rahulg007
09-28-2012, 12:55 AM
bro i have phone wid me but i dnt have multifun tool activation :( and bro aapka snork id kya hai???

Shadab Ahmad
09-28-2012, 01:09 PM
Contact me on Sonork : 100.1602669

Br,
Shadab Ahmad

umeshkumar shaw
11-04-2012, 12:17 PM
Hi All!

You can Unlock your N600+ MTS LiveWire permanently.

Just need a few files to be downloaded.

Download MTS Original Firmware ([Only registered and activated users can see links] 8%83/new/3G/%E8%BD%AF%E4%BB%B6/157750B0513V.MTS.SP100.B04.zip)

Download Chinese Firmware ([Only registered and activated users can see links] 8%83/%E5%A4%96%E5%8D%8F%E5%8E%82%E5%AE%B6/N600PLUSV1.0.1B06.zip)

Download Flasher ([Only registered and activated users can see links])

Extract firmware to any folder of your choice.
Install Flasher.

Now start flasher. On login screen, you will see strange characters.
Don't worry, just click on OK.

Now software will open, Click on English Version. Close flasher and again Run.

Now you will see Username and Password dialog. Type in the following:
User: Administrator
Pass: ZTEsmt123
and click OK.

Now flasher will start with all options enabled.

Connect phone in FTM mode by holding Volume Down Key and Power Key.

If you need driver, it is in our Support Area's ([Only registered and activated users can see links]) \Driver Folder.

Note down COMM Port in device manager (ZTE Diagnostic Port - DFU, something similar).

In flasher, goto Option > Port Config, and select noted COMM Port in Line1-DIAG and click OK.

Now flasher will show your phone information in main windows against Line 1 (1:).

Now, in Download Settings, Mark on Download CEFS. A message will come, simply click OK on that message.

In Config Group, select No Backup and Restore.

Click on SW Directory and select folder where you extracted Firmware.

Now Click on Arrow ( -> ) against your Line where phone information is being displayed (eg. Line1 ).

Flashing will start and will take something around 3 minutes.

Close flasher, do not disconnect phone, leave it connected in FTM mode.

Now start MultiFuN CDMA ZTE Module, select phone COMM Port, select Model as N600+ LiveWire and click on SP Unlock. Software will give you information that Unlocking was successful. :cool:

If you have any other tool supporting this Model, you can use that tool too.

Now, you can use your phone with any Carrier, no need to unlock it again and again.

Enjoy! ;)

Br,
Shadab Ahmad





which firmware i will download
plzzzz help

user.name
12-11-2012, 02:27 AM
Not till now.

Br,
Shadab Ahmad
any update? unlocking without meid zeroing?

user.name
12-11-2012, 02:29 AM
any update? unlocking without meid zeroing?

Shadab Ahmad
12-11-2012, 01:26 PM
any update? unlocking without meid zeroing?
Not yet.

Br,
Shadab Ahmad

zuberchowdhry
04-25-2013, 05:16 PM
Great Work by Multifun Tool Team,


I was trying to unlock ZTE-N600+

But after Flash Phone stuck on FTM Mode,

Then i Connect Phone to USB again & Run Multifun ZTE Tool,

Only Clicking SP Lock, my Phone Unlock & even Fixed the stuck on FTM Mode,

Here is the Logs:
[03:48:39] Initializing...
[03:48:39] Port: COM8
[03:48:39] Baud: 115200
[03:48:39] Device: ZTE N600+
[03:48:39] Operation: SP UNLOCK
[03:48:39] Port Opened
[03:48:39] Compile: Apr 20 2011 04:41:21
[03:48:39] Release: Aug 04 2010 16:00:00
[03:48:40] MEID: 00000000000000
[03:48:40] Unlocking Phone...
[03:48:40] Phone Unlocked.
[03:48:40] Restarting Phone...
[03:48:40] Operation Finished.
[03:48:41] Port Closed.
[03:48:41] Time Taken: 00:02


Small Tool but great work,

Enjoy Multifun Tool.


BR,
ZUBER

sudhir1980
05-13-2013, 01:39 AM
:confused:You can download it from our Download Area [Only registered and activated users can see links]

Username/Password: multifun

Br,
Shadab Ahmad

arup.c
05-19-2013, 07:54 PM
How do I get the MultiFuN CDMA ZTE Module. It is not available in support.

sudhir1980
06-06-2013, 12:52 PM
Hi All!

You can Unlock your N600+ MTS LiveWire permanently.

Just need a few files to be downloaded.

Download MTS Original Firmware ([Only registered and activated users can see links] 8%83/new/3G/%E8%BD%AF%E4%BB%B6/157750B0513V.MTS.SP100.B04.zip)

Download Chinese Firmware ([Only registered and activated users can see links] 8%83/%E5%A4%96%E5%8D%8F%E5%8E%82%E5%AE%B6/N600PLUSV1.0.1B06.zip)

Download Flasher ([Only registered and activated users can see links])

Extract firmware to any folder of your choice.
Install Flasher.

Now start flasher. On login screen, you will see strange characters.
Don't worry, just click on OK.

Now software will open, Click on English Version. Close flasher and again Run.

Now you will see Username and Password dialog. Type in the following:
User: Administrator
Pass: ZTEsmt123
and click OK.

Now flasher will start with all options enabled.

Connect phone in FTM mode by holding Volume Down Key and Power Key.

If you need driver, it is in our Support Area's ([Only registered and activated users can see links]) \Driver Folder.

Note down COMM Port in device manager (ZTE Diagnostic Port - DFU, something similar).

In flasher, goto Option > Port Config, and select noted COMM Port in Line1-DIAG and click OK.

Now flasher will show your phone information in main windows against Line 1 (1:).

Now, in Download Settings, Mark on Download CEFS. A message will come, simply click OK on that message.

In Config Group, select No Backup and Restore.

Click on SW Directory and select folder where you extracted Firmware.

Now Click on Arrow ( -> ) against your Line where phone information is being displayed (eg. Line1 ).

Flashing will start and will take something around 3 minutes.

Close flasher, do not disconnect phone, leave it connected in FTM mode.

Now start MultiFuN CDMA ZTE Module, select phone COMM Port, select Model as N600+ LiveWire and click on SP Unlock. Software will give you information that Unlocking was successful. :cool:

If you have any other tool supporting this Model, you can use that tool too.

Now, you can use your phone with any Carrier, no need to unlock it again and again.

Enjoy! ;)

Br,
Shadab Ahmad
Phone working but wifi not working when try to active wifi msg. display "error"

Shadab Ahmad
06-07-2013, 01:46 PM
Phone working but wifi not working when try to active wifi msg. display "error"
You can reppair WIFI, if you have MultiFuN Tool.

Br,
Shadab Ahmad

sudhir1980
06-07-2013, 04:04 PM
You can reppair WIFI, if you have MultiFuN Tool.

Br,
Shadab Ahmad
Dear Brother Shadab Ahmad I have multifuntool and I write my MEID No. in original phone's MEID No. but ESN I don't know please tell me full process to enable wifi. Thanking You:confused:

mashuk
06-12-2013, 10:50 PM
Hi All!

You can Unlock your N600+ MTS LiveWire permanently.

Just need a few files to be downloaded.

Download MTS Original Firmware ([Only registered and activated users can see links] 8%83/new/3G/%E8%BD%AF%E4%BB%B6/157750B0513V.MTS.SP100.B04.zip)

Download Chinese Firmware ([Only registered and activated users can see links] 8%83/%E5%A4%96%E5%8D%8F%E5%8E%82%E5%AE%B6/N600PLUSV1.0.1B06.zip)

Download Flasher ([Only registered and activated users can see links])

Extract firmware to any folder of your choice.
Install Flasher.

Now start flasher. On login screen, you will see strange characters.
Don't worry, just click on OK.

Now software will open, Click on English Version. Close flasher and again Run.

Now you will see Username and Password dialog. Type in the following:
User: Administrator
Pass: ZTEsmt123
and click OK.

Now flasher will start with all options enabled.

Connect phone in FTM mode by holding Volume Down Key and Power Key.

If you need driver, it is in our Support Area's ([Only registered and activated users can see links]) \Driver Folder.

Note down COMM Port in device manager (ZTE Diagnostic Port - DFU, something similar).

In flasher, goto Option > Port Config, and select noted COMM Port in Line1-DIAG and click OK.

Now flasher will show your phone information in main windows against Line 1 (1:).

Now, in Download Settings, Mark on Download CEFS. A message will come, simply click OK on that message.

In Config Group, select No Backup and Restore.

Click on SW Directory and select folder where you extracted Firmware.

Now Click on Arrow ( -> ) against your Line where phone information is being displayed (eg. Line1 ).

Flashing will start and will take something around 3 minutes.

Close flasher, do not disconnect phone, leave it connected in FTM mode.

Now start MultiFuN CDMA ZTE Module, select phone COMM Port, select Model as N600+ LiveWire and click on SP Unlock. Software will give you information that Unlocking was successful. :cool:

If you have any other tool supporting this Model, you can use that tool too.

Now, you can use your phone with any Carrier, no need to unlock it again and again.

Enjoy! ;)

Br,
Shadab Ahmad

YOUR process worked for me but touch screen is not working at all my calibration is not at all right now it become correct if I left my device for a day but when it start working the touch start shifting and finally becomes unresponsive touch screen. for ex if I want to press dialer button then I have to touch message button
pl help me

Maikano
07-02-2013, 06:34 PM
Please, I have downloaded the three files, but am having a problem of logging into the support area. The user name "multifun" and password are not working, and I need to download the MultiFuN CDMA ZTE Module.

Maikano
07-05-2013, 05:48 AM
Please, I still can not log on into the support area. The username of "multifun" and password are not working

himanshu9
03-12-2014, 08:28 PM
i could not able to download multifun zte module.
user id and password is showing incorrect of multifn/support

Shadab Ahmad
03-13-2014, 01:51 PM
Its told many time that its
Username: mftool
Password: mftool

Br,
Shadab